Two engineers stand beside the same aircraft before an early flight. One is under the wing, checking a hydraulic line for leaks. The other is in the avionics bay, tracing a fault on a navigation unit. Both will sign for the same aircraft, yet their training took different routes from the third semester onwards.

That is how the aircraft maintenance engineering course is built. You choose a stream, and the stream decides what you spend most of your hours learning. If you are comparing aircraft maintenance engineering colleges, understanding that split early saves a lot of confusion.

AME Course Details: How the Programme Is Organised

HIET runs three categories under its AME course. B1.1 (aeroplane turbine) and B1.3 (helicopter turbine) are the mechanical streams. B2 is the avionics stream. B1.1 and B2 each run for two and a half years across five semesters, and B1.3 runs for two years across four.

The hours are published in HIET’s syllabus. B1.1 and B2 each add up to 2,620 hours: 1,568 of theory, 764 of in-house practical work and 288 at an approved maintenance organisation (AMO). B1.3 comes to 2,520 hours: 1,504 of theory, 716 of practical work and 300 at an AMO. These aircraft maintenance engineering course details show how much of the course is hands-on, so read them before you pick a stream.

The Mechanical Stream: B1.1 and B1.3

Mechanical engineers look after the structure, the engines and the mechanical systems. In B1.1 that means airframes, flight controls, hydraulics, fuel systems, landing gear, ice and rain protection, pressurisation and oxygen. Gas turbine engines run across the fourth and fifth semesters, with propellers alongside in the fifth.

The workshop side is physical. Students work on riveting, sheet metal, welding, pipe bending and cable swaging, and they learn to inspect for corrosion and fatigue damage.

B1.3 applies the same thinking to helicopters. Its biggest block, 282 hours of theory, covers helicopter aerodynamics, structures and systems: rotor heads, swash plates, tail rotors, blade tracking, vibration analysis and transmissions.

The Avionics Stream: B2

Avionics is the electronic side of the aircraft. It covers navigation instruments, communication equipment, radar and the autopilot.

B2 students spend more time on electronics than their mechanical classmates do. In the subjects both streams share, they go deeper into transistors and operational amplifiers, and they add microprocessors and multiplexing that the mechanical stream leaves out. The later semesters turn to instruments, radio and navigation systems (VHF and HF, VOR, ILS, DME, GPS, TCAS and weather radar), electrical power, autopilot and auto-landing, and cabin and information systems. Turbine engines still appear, but in a single lighter subject on engine indication, starting and ignition.

The practical work involves wiring, connectors, crimping, soldering and avionic test equipment. For students who want a degree alongside, there is the B.Sc Avionics. HIET lists it under the avionics stream, and its graduates can look at roles such as avionics technician, AME specialising in avionics, avionics system designer and system integrator.

Where the Two Paths Meet

The first two semesters are almost identical. Everyone studies electrical fundamentals, electronic fundamentals, basic aerodynamics, digital techniques, maintenance practices and aviation legislation. Human factors arrives in the fourth semester, and in B1.1 and B2 the first 144 AMO hours arrive then too.

Human factors shows what is shared. It teaches how fatigue, stress and poor communication lead to maintenance errors, which matters to a hangar engineer and an avionics engineer in equal measure. Each stream then prepares you for its own DGCA licence category, so the choice you make here carries through to the licence you aim for.

Adding a B.Sc to the AME Course

Students admitted to the DGCA course can take a B.Sc at the same time. The options are B.Sc Aircraft Maintenance Engineering and B.Sc Avionics, both three years and both awarded by Hindustan Institute of Technology and Science (HITS). The degree is optional, and only students admitted to the DGCA curriculum can take it. For the B.Sc Aircraft Maintenance Engineering, HITS says the course is UGC approved and that 90% attendance is needed to sit exams.

When you look at B.Sc aircraft maintenance engineering colleges, ask whether the degree and the licence training run side by side or one after the other. Side by side should save you time.

Choosing Between Mechanical and Avionics

A few honest questions help. Do you like taking things apart to see how they fit? Mechanical suits you. Would you rather follow a circuit diagram until you find where a signal stops? That points to avionics, and the B.Sc Avionics is worth asking about too. If helicopters are what pulled you towards aviation, B1.3 exists for that reason.

Then ask every one of the aircraft maintenance engineering colleges on your list for the syllabus, not the brochure. Read the AME course details module by module and see how the hours are split. HIET puts its syllabus for B1.1, B2 and B1.3 on its website, so you can do this before you visit.

Studying the Aircraft Maintenance Engineering Course at HIET

HIET offers all three categories, with DGCA approval under CAR 147 (Basic) for B1 and B2 since 2018 and for B1.3 since 2022. Students train in a 9,000 sq ft Aero Hangar and in workshops and labs for engines, hydraulics, avionics, instruments and radio navigation. Admission needs Class 12 with Physics, Chemistry and Mathematics, or an equivalent diploma.

If B.Sc aircraft maintenance engineering colleges are on your shortlist, HIET offers the degree alongside the DGCA course through HITS. The full aircraft maintenance engineering course details, including fees, eligibility and dates, are at www.hiet.in. You can also call 96000 07444.